1
(name and SID#)
Department of Materials Science and Engineering
School of Engineering and Applied Science
University of California, Los Angeles
MSE 122
Principles of Electronic Materials Processing
Comprehensive Exam 2015
This test consists of four problems. Clearly show your work and put a box around your
final answer for each problem. STUDENTS ARE ALLOWED TWO
EQUATION SHEETS (8.5” x 11”), A CALCULATOR, AND A RULER
1) (35)
2) (30)
3) (35)
4) (15)
Total) (115)
Note: Displacement energy for implants into silicon: Ed = 15 eV
2
1) Ion implantation is an important technique for semiconductor
processing. To produce a p-n junction in an n-type (1015 cm-3
) substrate, it
is necessary to implant with boron or another species.
(A) For an implant energy of 50 keV and a peak boron concentration of 5?1018 cm-3
,
sketch the boron profile (calculate for five points) and determine the junction
depth(s).
(B) Is this sufficient (energy, dose) to make the material amorphous? Explain
(C) Germanium is sometimes used to pre-amorphize a silicon wafer. What energy and
what dose is required to make the layer amorphous by the Ge implant (I know that
you don’t have the implant curve for Ge in silicon below – improvise) so that the
maximum implanted Ge concentration location matches the maximum boron
concentration from part a)?
3
(D) What is the change in junction depth in (A) change if annealed at (i) 1000 °C for
30 minutes; (ii) 550 °C for 30 minutes? Answer quantitatively although you may
estimate (show your reasoning) an answer for (ii). Please note there is a graph at the
end of the test that may be of help.
(E) What benefits accompany amorphization? Answer qualitatively.
4
2) AlxGa1-xAs is an alloy semiconductor that can be grown by either
OMVPE or MBE.
(i)
a) (a) Define OMVPE and MBE.
b) What are the key benefits of OMVPE compared to halide or hydride VPE?
(ii) Describe two main points about each technique (MBE and OMVPE) from the
‘tour’.
(iii) The graph below shows a RHEED pattern during MBE for a structure that
consists of the deposition of a layer of GaAs, followed by AlxGa1-xAs, followed by AlAs.
What is the thickness of the AlAs and the GaAs layers ( in “monolayers”)?
What is the alloy composition?
(iv) If the Al cell temperature during that MBE growth is 1000 °C, determine the
temperature of the Ga cell to achieve the behavior in the RHEED (or relative fluxes) data
assuming that the Al (MW = 27) and Ga (MW=69) cells are otherwise identical. You
may neglect the explicit dependence of the flux on temperature for this comparison (in
other words, a certain temperature will correspond to a certain vapor pressure. However,
there is a separate temperature term in the denominator. Ignore the term in the
denominator.)
5
6
3) A p-type <111> oriented silicon wafer (1015 cm-3
) is placed in a wet
oxidation system to grow a field oxide of 600 Å at 1000 °C.
i) Determine the time required to grow the field oxide.
ii) After this first oxidation, the oxide over region A is removed. Then a
diffusion step is carried out in which phosphorus is diffused into the wafer and
the surface concentration of phosphorus is 3×1020 cm-3
. Next, a dry oxidation
step is performed at 900 °C for 60 minutes. Find the thickness of the oxide
over region A and the new thickness of the oxide over the other area (B in the
figure below). Ignore any chemical or structural differences in the field oxide
and gate oxide in terms of the oxidation kinetics.
Explain why wet oxidation is used for the field oxide and dry oxidation is
used for the gate oxide.
iii) Explain the difference between mass-transport limited oxidation and
reaction-rate limited oxidation. Under what oxide growth conditions would
each of these be expected?
7
Wet Oxidation ?
8
9
10
4) True/False / Fill-in-the blanks / short answers
a) The typical precursors for silicon VPE growth are
.
b) Is Ni or P a faster diffuser in Si? Why?
c) A high phosphorus concentration in a silicon wafer will increase the oxidation
rate during the growth of a thick oxide. T / F
d) Mass separation is achieved in ion implantation by electrostatics. T F
e) PAC stands for:
f) The ratio of the oxidation linear reaction rate constants B/A (111) to B/A (100) is
related to:
g) I-line refers to:
h) Draw epitaxy growth rate vs. inverse temperature graphs for a system whose
formation reaction is (a) endothermic and (b) exothermic
11
ScholarMatic | 24/7 Homework Help
ScholarMatic Will Help You Write Your Essays and Term Papers
Answered » You can buy a ready-made answer or pick a professional tutor to order an original one.
MSE 122 Comprehensive Exam 2015
HOME TO CERTIFIED WRITERS

Why Place An Order With Us?
- Certified Editors
- 24/7 Customer Support
- Profesional Research
- Easy to Use System Interface
- Student Friendly Pricing
Have a similar question?
ScholarMatic: Get Started
Assignment Writing Service
Feel safe and secure when placing an order on our portal!
Fruitful cooperation begins with solid guarantees, and we are professional enough to promise perfect results. Let’s get it started!




